China manufacturer of magnetic ballasts for metal halide flood lights & hps flood lights

Almost all the customers buy the lamps will be consulting the installation, always worried about whether the package installation, if the service there is no way to install the how to do, the commonly used lamps and lanterns are crystal lamp, crystal pendant, fluorescent light fixture, marble lamps, we are dedicated to the to according to the different kinds of home lighting installation, chandeliers, ceiling lamps, wall lamps, has its own installation method to everybody as below:

(一) installation requirements:

1 lamps and accessories should be complete, there should be no mechanical damage, deformation, paint peeling and lamp cover rupture and other defects

2 the load carrying capacity of the fixed part of the wall mounted ceiling mounted light fixture shall be matched with the weight of the lamp

3 the lamp should be equipped with hanging line box, each hanging line box can only be installed a set of pendant lamp. The surface of the pendant lamp must be well insulated, and there may not be a joint, and the wire cross section shall not be less than 0.4 mm. In the wiring box hanging line should be taken to prevent thrum stress the lamp drop measures. Weighed more than a kilogram of lamps should be arranged chain. When the chandelier lamp weight more than 3 kg, should use the embedded hook or a bolt fixed. The chain lamp line should not be subject to tension, and the lamp wire should be compiled with fork chain

4 the incandescent lamp as the light source of ceiling lamp can not be installed directly on the flammable component; lighting shall be close to the lampshade; when the lighting and insulation between the distance less than 5 mm, lighting and insulation between Taiwan should take heat insulation measures. The power of an incandescent lamp shall not exceed the maximum power allowed by the lamp.

5 fluorescent lamp as the light source, ballast should be installed in the phase, the lamp should prevent lamp foot off shell and stay in the lamp box internal margin, giant lights and the frame of the roof decorative lines are parallel, the lamp frame should be close to the roof surface

6 Light socket should be grounded in the center contact terminals, zero line should be grounded on the thread of the terminal, lamp holder of the insulated shell should be complete, no damage and leakage phenomenon

7 fixed lantern hook, its diameter should not be less than the diameter of the lamp and the lamp hanger, a minimum of not less than 6 mm

(二) installation method of several lamps:

1: the chandelier installed in the top surface of the concrete, the embedded parts, bolts and bolt penetrating tube expansion. When installing the theme and the weight of the visible light to determine the tube expanding bolt specifications, but the minimum should not be less than M6 (mm), bull droplight should not be less than M8 (mm), the number of bolts at least less 2 pieces. Light self tapping screws for expanding tubes can not be used

2 ceiling lamp has a circular, square or rectangular base (chassis), base size range. The base of the lamp can bolt expansion pipe, can also use wood screws in embedded block fastening. If the holder base diameter over 100 mm, must use the 2 screws. If the base of the lamp is installed, the bolt diameter shall not be less than 6 mm in diameter. The lamp can be fixed on the bottom of the machine. The number of wood screws should not be less than the number of the lamps.

3: according to the structure of the base wall lamp wall lamp can be used or no base station base station. With the base station should be fixed base station, and then the lamp is fixed on the bottom table. The end table is generally made of wood, and the thickness of the board should be more than 15 mm, and the surface of the paint is painted. Wall lamp installation can use light box installation screw hole into screw to fix the, also can be in the walls of the drilling, pre buried wood blocks or plastic expansion pipe screws to fix. Wall lamp base screw is generally less than 2 pieces. The installation height of wall, ground 2~2.2 meters away from the center of the installation of the general lighting, wall lamp with 1.2 ~1.4 meters is appropriate

4: downlight is suitable for embedded lamps, ceiling. Basic form of lamps and lanterns is cylindrical, mouth lamp for plating lead, titanium or nickel plated metal broadside ring, in the lamp installed later, close to the top surface, good decorative. The lamp tube has a symmetrical on both sides of the clamping spring device is fixed as downlight. The opening in the lamp opening direction, spacing adjustment nut spring by the butterfly. Installation steps:

5 according to size downlight, installation position in the ceiling on scribing and drilling 6 will the ceiling reserved power supply line with downlight connecting through adjusting the lamp fixed spring leaf butterfly nut, the spring piece and the height of the ceiling thickness of the same downlight pushed into the ceiling opening hole, and fitted with a suitable bulbs